Tyre pressure is the cheapest performance change available on a bike, and the one most riders get wrong. There is nothing to buy. It is a number, a pump, and two minutes. Get it right and you gain rolling speed, grip, and comfort at the same time.
The pressure moulded into your sidewall is a safety limit set by the manufacturer, not a recommendation. Your optimal pressure depends on your weight, your measured tyre width, the surface you ride on, and how fast you ride it. That is four variables a rule of thumb cannot hold, and a calculator can.
Most road riders on 25 to 30 mm tyres land between about 52 and 102 psi. The right number falls as the tyre gets wider and rises with rider weight. Treat this table as a starting point, then use the calculator below for your own number.
| Rider weight | 25 mm tyre | 28 mm tyre | 30 mm tyre |
|---|---|---|---|
| 55–59 kg (121–130 lb) | 70 / 73 | 58 / 61 | 52 / 55 |
| 60–65 kg (132–143 lb) | 73 / 75 | 61 / 67 | 55 / 58 |
| 66–70 kg (146–154 lb) | 75 / 84 | 67 / 70 | 58 / 61 |
| 71–75 kg (157–165 lb) | 84 / 91 | 70 / 77 | 61 / 67 |
| 76–80 kg (168–176 lb) | 91 / 99 | 77 / 84 | 67 / 70 |
| 81–85 kg (179–187 lb) | 99 / 102 | 84 / 87 | 70 / 73 |
Each cell shows front / rear pressure in psi. The figures are Schwalbe's published pressures for the Pro One TLE on a 19 mm inner width rim, converted from bar at 14.5 psi per bar. Other tyres, wider rims and sealant change the answer. Never exceed the maximum printed on your tyre or rim.
Harder rolls faster, until it does not. Past the point SILCA calls breakpoint pressure, the energy lost to you and the bike vibrating over the road outweighs anything gained from a smaller contact patch. Above it, more pressure makes you slower.
SILCA's road testing puts the cost of running 10 psi below the breakpoint at roughly 1 watt, against about 9 watts for running 10 psi above it. If you are estimating, estimate low. Most riders estimate high.
Two riders 30 kg apart on identical tyres have meaningfully different optimal pressures, and so does the same rider on fresh asphalt and on chipseal. A single number printed on a sidewall cannot express that.
SILCA's test results in watts, at the breakpoint pressure and at 10 psi either side of it, on three road surfaces. The test used Continental GP 4000 II tyres. Where both sides were tested, running under cost far less than running over.
| Road surface | 10 psi under | Breakpoint | 10 psi over |
|---|---|---|---|
| New asphalt | 44 W | 43 W | 52 W |
| Coarse asphalt | 49 W | 48 W | 54 W |
| Rough milled concrete | Not tested | 62 W | 65 W |
SILCA's calculator is the most rigorous public tool for this. It is built on rolling resistance data collected on real road surfaces using the Chung method, not on a steel drum in a lab. We link to it rather than build our own, because there is no sense duplicating the tool that is already the reference.
One caveat worth repeating from SILCA: the calculator does not know your rim and tyre limits. Hookless and tubeless setups have hard maximum pressures. Where the manufacturer's figure is lower than the calculator's, the manufacturer wins.
Where the breakpoint comes from, what the testing actually measured, and the one thing a pressure calculator can never tell you about your tyres.
A calculator sets your pressure for today's ride. Componentry tracks what every ride does to your tyres, chain, cassette, and brake pads, and tells you what needs replacing before it fails on you.
Start your 2-month free trial. No credit card required.